Login

Remember

Register

Categories
Ask a Question
Complaint & Advise
Warranty Inquiry
Unpack Videos

How we can do send and change the state to receive in same time using RS485 ?

0 like 0 dislike

162 views

asked in T20 by jason Q&A Engineer (11.2k points)

Please log in or register to add a comment.

Please log in or register to answer this question.

1 Answer

0 like 0 dislike

answered by jason Q&A Engineer (11.2k points)
edited by jason

Because the mechanism of RS485 itself is half duplex,so cannot send and receive in same time.It is the default 'receive' state of the machine. When the 'send' state is required, the software needs to switch to the 'send' control, and then switch to the 'receive' state after sending data

Please log in or register to add a comment.

Related questions

0 like 0 dislike

1 answer 591 views

my main issue for now, is managing to handle Ultralight EV1 tag. for that we are used to send raw APDU. I have tried, to use the nfc.transmit method, but I suppose it needs to receive more than just the basic apdu code, and it's more low level than I expect. Basically I'm used to transceive : 0x60 -> GET_VERSION 0x1B... -> PWD_AUTH 0x30... -> FAST_READ ... But here passing those value give me errors. I had no issue using the m1_authenticate m1_read_block m1_write_block If you have some sample code, managing to read/write or send the GET_VERSION apdu to an ultralight code, it should be enough for me to take after.

asked in T20 by jason Q&A Engineer (11.2k points)

0 like 0 dislike

1 answer 183 views

Would you tell us commands to change the qr scanning mode in Telpo T-20? We need to turn off the scanner after scanning. now the problem is that the scanner does not turn off after reading and immediately reads the same qr

asked in T20 by jason Q&A Engineer (11.2k points)

0 like 0 dislike

1 answer 373 views

Hello team, I was able to check the demo for the NFC Mifare classic. The problem with the demo is you need to press a button to open the nfc, then you need to press another to authenticate and finally press another to read. With our app we need to be able to do all this steps without user interaction. Apart from that we need the app to be listening all the time for an incoming nfc tag. That’s why I was asking you last time if there’s something like a listener similar to the one you have with the QR Reader (setHardReaderListener). I would really appreciate if you can help me with this. Thank you.

asked in T20 by jason Q&A Engineer (11.2k points)

0 like 0 dislike

1 answer 245 views

for the QR reader - we are using the telpo_api with RSReader class as in TPS530 devices. But we don't receive any bytes using rsReader.rs_read() the QR reader beeps and recognizes the QR code, but there are no bytes coming from RSReader

asked in T20 by jason Q&A Engineer (11.2k points)

0 like 0 dislike

1 answer 214 views

We would like to use the face recognation with Telpo20 device. May you help me , where can I find this feature in the demo, otherwise may you send me a demo with it?

asked in T20 by jason Q&A Engineer (11.2k points)

0 like 0 dislike

1 answer 195 views

do you have documentation/examples for Mifare Desfire Cards of VP3300? We can work with mifare classic cards but we couldn't figure out how to use the mifare desfire cards

asked in T20 by jason Q&A Engineer (11.2k points)

0 like 1 dislike

1 answer 314 views

how can we run the app in kiosk mode and How can we prevent the installation of third parties applications?and auto restart app?

asked in T20 by jason Q&A Engineer (11.2k points)

0 like 0 dislike

0 answers 160 views

Actually, the SDK provided with the device is working on Android Gradle 7.0.3 which is quite old. We tried to upgrade the Gradle to 8.4 version but we faced issue. We would like to get confirmation from you that its possible to upgrade Android and Gradle version and still use your SDK. also can we upgrade the Android firmware in order to use flutter for some app development ?

asked in S10 by jefpro Q&A Freshman (102 points)

0 like 0 dislike

1 answer 202 views

In our app we need to track the bus location and we can’t use the gms for fusedLocation. What is your suggestion in this case?

asked in T20 by jason Q&A Engineer (11.2k points)

0 like 0 dislike

1 answer 186 views

T20 After the installation of application we need to deactivate touch screen (to prevent from accidental touches). Only Barcode reader should be active. How can we manage this?how to set kiosk mode

asked in T20 by jason Q&A Engineer (11.2k points)

Welcome to Telpo Q&A,

If you have a technical question ,please ask here, in English.
.
If you have faulty devices need be repaired,please create a issue ticket.

Please inquiry your ticket.

Notice :If you have an urgent question or cannot register account of Q&A, you can contact the online support in below jivochat .

Categories

All categories
Handheld Pos (99)
Desktop Pos (36)
Cash Register (10)
TIcket Validator (115)
- T20 (70)
- TPS530 (32)
- T10 (13)
Kiosk (19)
VloT (22)
Platform (23)
UnCategory (24)

Send feedback

Snow Theme by Q2A Market

Powered by Question2Answer

...